🇪🇺 Over the past few months I've been experimenting a lot with cameras (it's related to the #Sunchronizer, but I'm not revealing exactly what yet). To connect the camera properly with my RaspberryPi5, I also designed a small housing. It allows mounting the Raspberry Pi GS or HD Camera at an angle.
Build details are available here: /Nerdiyde/Nerdiy_Products/tree/main/products/raspberry-pi5-angled-mount-for-raspberry-pi-gs-or-hd-camera or in the bio.
🇩🇪 In den letzten Monaten habe ich viel mit Kameras experimentiert (Es hat mit dem #Sunchronizer zu tun, aber was genau verrate ich noch nicht.) Damit ich die Kamera auch passend mit meinem RaspberryPi5 verknüpfen kann, habe ich natürlich auch ein kleines Gehäuse entworfen. Darin kann die Raspberry Pi GS oder HD Kamera montiert werden.
Infos zum Nachbau findet ihr unter: /Nerdiyde/Nerdiy_Products/tree/main/products/raspberry-pi5-angled-mount-for-raspberry-pi-gs-or-hd-camera oder in der Bio.
#nerdiy #raspberrypi #raspberrypi5
🇪🇺 As someone who has accidentally left the soldering iron on at my desk more than once in the past, I have been fully switching my desk setup on and off for a few years now. So far, I used Zigbee buttons. Unfortunately, they are battery-powered, and it feels like I am replacing batteries all the time.
To solve this once and for all, I designed a small Safety Switch Board.
It has six switches that let me turn my desk, lights, and a few other desk devices on and off. Internally, I use a @seeedstudio XIAO ESP32-S3 to read the switch states and forward them to my #HomeAssistant.
The firmware is based on #ESPHome. Firmware, build details, and STL files are available here: /Nerdiyde/Nerdiy_Products/tree/main/products/6x-safety-switch-desk-mounting-board-for-xiao-esp32-s3
#nerdiy #safetyswitchboard #xiaoesp32s3
🇪🇺 To control the azimuth/rotation axis of the #Sunchronizer, I use a 3D-printed worm gear. The worm is then driven by another spur gear and a 12V motor to rotate the Sunchronizer assembly on the 3D-printed slewing ring.
It already works very well. At the same time, I see the most potential for improvement here. How would you do it? 🙂
🇩🇪 Um die Azimuth/Rotationsachse vom #Sunchronizer zu steuern nutze ich ein 3D gedrucktes Schneckengetriebe. Die Schnecke wird dann über ein weiteres Stirnradgetriebe und einen 12V Motor angetrieben um den Aufbau des Sunchronizers auf dem 3D gedruckten Drehkranz zu drehen.
Es funktioniert so schon sehr gut. Gleichzeitig sehe ich hier auch noch am meisten Verbesserungspotential. Wie würdet ihr es machen? 🙂
#Nerdiy #Nerdy #caddesign #3dprinting #soldering #doityourself #electronics #technology #engineering #maker #esp32 #project #esphome #electricalengineering
🇪🇺 And since I was busy developing camera housings for the #Raspberry Pi and #raspberrypicamera, I simply made another one that allows for a more compact camera mount... 😌
You can find the STL files for printing yourself in my shop (link in bio). 🙂
🇩🇪 Und weil ich gerade dabei war Kameragehäuse für den #Raspberry Pi zu entwickeln, habe ich einfach noch eins gemacht, bei dem die Kamera etwas kompakter montiert werden kann... 😌
Die STL Daten zum selber drucken findet ihr in meinem Shop (link in Bio). 🙂
#Nerdiy #Nerdy #caddesign #3dprinting #soldering #doityourself #electronics #technology #engineering #maker #esp32 #project #esphome #electricalengineering
@berrybase.de@raspberrypi
🇪🇺 For a project, I needed a simple camera housing for the @raapberrypi camera and the Raspberry Pi. So, I quickly fired up the CAD tool, and voila, a new housing design was born. Thanks to the tripod thread, the camera constructed this way can also be mounted on a simple photo tripod. You can find the housing in my shops. Link in bio.
What special housing are you still missing for your Raspberry Pi? 🙂
🇩🇪 Für ein Projekt brauchte ich ein einfaches Kameragehäuse für die Raspberry Pi Kamera und den RaspberryPi. Also "schnell" das CAD Tool angeworfen und voila ein ein neues Gehäusedesign ist geboren. Dank Stativgewinde kann die so aufgebaute Kamera auch auf einem einfachen Fotostativ verbaut werden. Das Gehäuse findet ihr in meinen Shops. Link in Bio.
Welches besondere Gehäuse fehlt euch noch für euren Raspberry Pi? 🙂
#Nerdiy #Nerdy #caddesign #3dprinting #soldering #doityourself #electronics #technology #engineering #maker #esp32 #project #esphome #electricalengineering
🇪🇺 Of course, I also continued working on the #Sunchronizer (a dual-axis tracker for a solar panel). The latest iteration has been out in the wild for a few weeks now. I've since made some design changes and scaled back some of my overengineering. I'll publish details about that in a YouTube video sometime soon. 🙂
🇩🇪 Natürlich habe ich auch am #Sunchronizer (ein Dual Axis Tracker für ein Solarpanel) weitergearbeitet. Die letzte Iteration jst seit ein paar Wochen draußen in der Wildnis. Mittlerweile habe ich einige Designänderungen vorgenommen und mein Overengineering etwas zurückgeschraubt. Details dazu werde ich mal in einem YouTube Video veröffentlichen. 🙂
#Nerdiy #Nerdy #caddesign #3dprinting #soldering #doityourself #electronics #technology #engineering #maker #esp32 #project #esphome #electricalengineering
🇩🇪 In most situations, the @raspberrypi integrated ports are sufficient. But sometimes you just need something more. 😎 For this, you can use the Waveshare USB 3.0 Expansion PCB, for example. This connects internally via the PCIe interface and expands the Raspberry Pi by four additional full-featured USB 3.0 ports.
You can find the matching case at Nerdiy.de/shop 🙂
🇪🇺 In den meisten Situationen reichen die integrierten Anschlüsse des RaspberryPi aus. Manchmal muss es aber halt etwas mehr sein. 😎 Dafür kann man zum Beispiel das Waveshare USB3.0 Erweiterunsg PCB nutzen. Dies wird intern über das PCIe intergace angebunden und erweitert den RaspberrPi so um vier weitere vollwertige USB3.0 Anschlüsse.
Das passende Gehäuse dazu findet ihr unter Nerdiy.de/shop 🙂
#Nerdiy #Nerdy #caddesign #3dprinting #soldering #doityourself #electronics #technology #engineering #maker #esp32 #project #esphome #electricalengineering
🇪🇺 I've been away for a while, but I've still been busy. 😎
There are a lot of new projects and updates to older ones. In the pictures, you can see the now quite large family of @raspberrypi cases for various HATs.
🇩🇪 Ich war eine Zeitlang abwesend aber trotzdem fleißig. 😎
Es gibt eine Menge neue Projekte und Updates älterer Projekte. Auf den Bildern seht ihr die mittlerweile ziemlich groß gewordene Familie an RaspberryPi Gehäusen für verschiedene HATs.
#Nerdiy #Nerdy #caddesign #3dprinting #soldering #doityourself #electronics #technology #engineering #maker #esp32 #project #esphome #electricalengineering
This housing for the @raspberrypi integrates the Waveshare Connector Adapter PCB and the Raspberrypi 4B in one housing and makes it possible to allign all connectors (w/o GPIO) to one side. This makes it much easier to integrate/use the Pi in a "Panelised" scenario. 🙂 Any feature that you are missing here?
#diy #3dprinter #3dprinting #raspberrypi #rpi #makerlife #maker
I finished the first prototype of my housing for the new @raspberrypi Touch Display 2. This comes with a resolution of 1280x720 pixel at 7" size. Perfect to display high resolution photos. 😍
But of course you need a proper housing. This fits tightly around the screen and integrates a RPi4 on the back. Also there is a place to mount an optional 40mm fan, a wall hanger and a standfoot is integrated. What are you using your rpi driven display for? 🙂
#raspberrypi #makerlife #3dprinter #3dprinting #rpi #display #diy
🇪🇺 It took a while, but I've finally finished three new segments for the #PrintAirPipe system. There are now two fan segments with which either a 120mm axial or 120mm radial fan can be integrated into the system. Thanks to the support of @pcbway , I have also designed a suitable PCB with which the built-in PWM fan can be controlled and read using a @seeedstudio XIAO ESP32 S3. The firmware is again based on #esphome and allows the target speed to be set but also the actual speed to be read.
Additionally I have now also published a filter segment to match this. This allows the pipe system to be expanded to include a HEPA filter and/or activated carbon filter. Based on this, I will soon also be offering sets for soldering extraction. 🙂 As always, I look forward to suggestions for other segments or sets that interest you. 🙂 More info at Nerdiy.de/papp
#Nerdiy #Nerdy #caddesign #3dprinting #soldering #doityourself #electronics #technology #engineering #maker #esp32 #project #esphome #electricalengineering
